2CM560 Digital stepper driver - 50V 6A Kinco

Driver pas à pas numérique Kinco 50V / 6A

2CM560 Digital stepper driver - 50V 6A Kinco

Driver Microstep 2CM560
- 50V - 6A
- 8 levels of current adjustment from 1.8~6A
- 15 levels of resolution from 200~25,600 steps
- Inputs (Pulses/Dir or CW/CCW) 5~24V optocoupled with internal limiting resistor, TTL compatible
- Pulse input frequency up to 400KHz
- Motor parameters self-identification system
- Automatic current reduction in case of inactivity
- Overvoltage and overcurrent protection

79.80 € Without Taxes 79.8 EUR 79.80 €

79.80 €

~~95.76 €~~ 95.76 € with taxes

Brand
Max. Voltage
Max. current
Resolution setting
- DIP-switches
Weight
- 280 gr

This combination does not exist.

AJOUTER AU PANIER

Product Documents

Catalogue Kinco 2CM

Manuel Kinco Driver 2CM_

Internal Reference: 2CM560

Digital Micro-step Driver 2CM560

8 settable current level 1~6A
15 subdivision levels 200~25 600 steps
Inputs (Pulses/Dir or CW/CCW) 5~24V opto isolated, TTL signal compatible
Input frequency up to 400kHz
Support parameter self-adaptive function
Automatic half-current function
Test-running
Over voltage and over current protection function
Micro-step filter function can smooth input pulse to reduce trasient motion of motor, make sure motor run more smoothly.
Nema 23 and Nema 24 motors compatible

Item	Description
Input Voltage	24~50VDC
Overvoltage protection	85VDC
UnderVoltage protection	15VDC
OverHeat protection	80°C (Temperature of Thermistor)
Phase current (peak)	1.8/2.4/3/3.6/4.2/4.8/5.4/6 A – 8 settable values
Subdivision	200~25600 Pulses / revolution, 15 subdivision levels in total
Adaptable Motor	Nema 23 et nema 34
Input Signals	PLS (CW) - DIR (CCW) – FREE – Input voltage: 5~24VDC – Input current: 8mA@5VDC / 12mA@24VDC
Control Mode	Pulse control : PLS + DIR – CW/CCW
Output signal	ERR - open collector output - maximum current: 100mA
Operation Indicator	Combination of RUN and ERR Led indicates different status
Protection Circuit	Over voltage – Under voltage – Over current – Over heat
Cooling method	Nature air cooling
Operation environnement	Indoor - installed in the environnement free from direct sunlight – dust – corrosive gas – combustible gas – oil mist – steam and drip
Operation humidity	<85%RH – non-condensing or water drops
Operation temperature	0°C~40°C
Storage temperature	-20°C~70°C
Protection	IP20

Subdivision setting (Unit : Pulses/Rev.)				Current setting (Unit:A)
SW1	SW2	SW3	Si SW4=ON	Si SW4=OFF	SW6	SW7	SW8	RMS	Pointe
ON	ON	ON	200	1000	ON	ON	ON	4.2	6
OFF	ON	ON	400	2000	OFF	ON	ON	3.8	5.4
ON	OFF	ON	800	4000	ON	OFF	ON	3.4	4.8
OFF	OFF	ON	1600	5000	OFF	OFF	ON	3	4.2
ON	ON	OFF	3200	8000	ON	ON	OFF	2.5	3.6
OFF	ON	OFF	6400	10000	OFF	ON	OFF	2.1	3
ON	OFF	OFF	12800	20000	ON	OFF	OFF	1.7	2.4
OFF	OFF	OFF	25600	NA	OFF	OFF	OFF	1.3	1.8

Function	DIP setting	Description
PLS + DIR	SW6 & SW7 = ON – Others OFF	Set DIP switches according to functions required when power OFF. Power On driver : RUN Led blinking is GREEN & ERR Led is RED. It means settings takes effect. Then Power OFF driver – reset subdivision and current for normal use.
CW/CCW	SW7 & SW8 = ON – Others OFF
Micro-Step smooth & dynamic filter disable	SW5 & SW6 = ON – Others OFF
Micro-Step smooth filter enable	SW5 & SW7 = ON – Others OFF
Micro-Step dynamic filter enable	SW5 & SW8 = ON – Others OFF
Test motor parameter upon power on disable	SW6 & SW7 & SW8 = ON – Others OFF
Test motor parameter upon power on enable	SW5 & SW6 & SW7 = ON – Others OFF
Test-running	SW6 & SW8 = ON – Others OFF	Motor running @80RPM
Automatic half-current	SW5 = ON – Others OFF	Set SW5=ON to enable automatic half-current. Phase current will reduce to half of the set value after motor stops for 1.5s

Accessories

Specifications

Brand	Kinco
Max. Voltage	50 V
Max. current	6 A
Resolution setting	DIP-switches
Weight	280 gr

Suggested alternatives: Compare